Screen Protector for OnePlus 13 [3 Pack], Tempered Glass UV Set, 9H Hardness Scratch Resistant, Sensitive Touch, Full edge-to-edge coverage with a seamless fit

Just like any screen protector this one is difficult to apply. But if you are careful and follow the instructions, it will apply with less blemishes and better adhesion. UV cure glue is far and away the best choice! Hard tempered glass protects better than tpu. You may have to reprogram your fingerprint sensor, and enable screen protector / glove mode on your phone, but once you do the fingerprint sensor and touch input work flawlessly. The negative reviewers here must just be clueless / didn't follow the directions. If it's pulling off to easily you probably just didn't cure it with the light for long enough!

Uv screen protectors are the way to go if you're rocking a phone with a curved screen. I've used these kind of protectors on other phones and never had any issues. This is the first time I've tried a screen protector from this brand and I don't have any complaints with the product itself.I can confirm the fingerprint reader still works after adding the protector. It's the slightest bit more finicky since adding the protector but not bad at all.Took me a few tries to apply the screen as the surface I used wasn't as leveled as I thought and this caused the adhesive to run down one side when applying the screen. This caused a mess, but is not a fault of the product. I think an alignment tool would have been a great addition to the product, but you can free hand it well enough.I have the official aramid case from OnePlus and haven't had any issues with the screen impacting the case.Overall I highly recommend this to anyone who is looking for a glass screen protector for their OnePlus 13 that will also work with the fingerprint sensor.

Check the contents of the box first thing. I really liked this after installing my first one. Then when I had to replace it, I discovered that I only got 2 protectors when I paid for 3. I got 3 glasses but only 2 had the back covering to peel off before installing, so the 3rd one was useless. I screwed up the second install so now I am screwed. Too bad as there are few tempered glass choices for the OP 13.

UPDATE:After much frustration with this screen protector I've finally removed it. Fingerprint reader now works great and everything seems to work more smoothly! Lowering from 4 to 2 stars.Original Review:Fingerprint unlock does not work as well as before installation, which is the main reason I bought this...the description clearly says it's fingerprint compatible, but it's very difficult to register a new fingerprint, and hit and miss when unlocking.Other than that, the installation is tedious, but well documented. I took it slow and it turned out perfect. If you get any bubbles, just be patient and work them out. Just installed it so can't vouch for durability, but I did give it an extra five minutes on UV, so we'll see.If the fingerprint sensor worked better, this would be a definite five stars.

Perfect adhesion, but follow the instructions. This phone's fingerprint scanner is notorious for not working with screen protectors, so the fact this does register fingerprints is huge. Place the screen very slowly, starting from the back, and allow it to spread the liquid and combine with all 3 drops before lowering it completely.Edit: Disregard... After a week the bottom is peeling and fingerprints work 1/3 times. Not many great options.

First of all, I installed it with an optivisor magnifer, so I could see all the dust and smudges. No, it's not easy peasy. The glue when you put it on it's not like the video showed. Bubbles everywhere from the tube you squeeze it out of. Don't be alarmed they'll come out when you push on them. Phone must be leveled otherwise glue runs off onto your table and a b__tch to clean up later.Learn from me and put a news paper underneath.My biggest problem was to clean up after you masked off all your buttons and above your camera is a tiny little slot that's your speaker. You must cover that! Otherwise, you will not going to be able to hear from that speaker because the glue went in there. You must mask that tiny little slot.Other than that it's fine.The phone functions well.

I put similar screen protectors with similar processes on all my phones and have never had any issues, I watched the video for this and followed every step exactly and all 3 times the corners start separating within 24 hours. Get a different brand because this doesn't work