Muzata10Pack 3.3FT/1M LED Channel Black Aluminum U Shape LED Strip Channel with Transparent Clear Cover Easy Installation with Paper User Manual U1SW BT 1M

I used these to hang a light strip under my Fifth wheel. I used 3M double sided tape to secure these to the frame and they worked perfectly.

I've been working on improving my desk setup for a couple of years and have gone through many different LED bias lighting brands and configurations to try to get the look and functionality I was looking for. It's difficult to get LED strips to stay stuck to the bottom side of a desk but I got it to work reasonably well using clear Gorilla Tape. The problem was that you could clearly see the strips.I saw these channels demonstrated on a YouTube video and immediately ordered them for my desk. At the same time, I upgraded from Govee to LIFX light strips. The bottom line is that I think the end result looks fantastic and is exactly the look and functionality I've been after.The channel is fairly easy to cut to length using a hacksaw. The plastic cover can be cut using shears. The channel then attaches to the desk using retention clips that are screwed into the surface. This leads to my one complaint: The edges of the clips are extremely sharp. They're so sharp that they badly scratch the finish off of the channel if it accidentally slides during installation, which I did several times. If you look closely at the uploaded picture of the open drawer, you can see one of the deep scratches in the channel.Otherwise, it looks fantastic. You can no longer see the light strips at all. The strips are protected from accidentally being knocked loose. I've crashed into these channels several times with my chair and they don't budge. Another benefit to this installation is the fact that the channel acts as a heat sink, which keeps the LEDs from absorbing too much heat and will ultimately extend the life of the strips.I ran the channel underneath the front and side edges of the desk to give it an under-glow and also to provide light into the drawers when they open. The channel is installed on the side of the rear edge to provide bias lighting against the wall.This would be five stars if the clips weren't so hazardous to the black finish on the channel. Otherwise, I'm very happy with them.

Great assortment of corners. Track is large enough to conceal average size wire nuts.

Aluminum strips are of great quality, and hardware that came with it is awesome.Perfect for any custom project and make great under cabinet, kitchen lighting rails.Will definitely be buying more from this company.Great products.

We got this set to install LED strip lights for under-cabinet lights in our kitchen. They were relatively easy to affix to the cabinets with the included clips and the LED strip seems to stick well after cleaning the inside of the channel with alcohol. The clear cover is a bit of a challenge to install, but it can be done if you take your time and work slowly from one end to the other. Overall, I am satisfied with our new under-cabinet light setup!

In depth Review of Muzata Aluminum channel, clear cover, .25" depth.TL;DR: Decent aluminum channel, good fit with the lid and end caps, brackets no so much. Easily cutable with hack saw. would purchase again with what I know.Purchased the 1 meter (3.3 foot) aluminum channel, 10 pack. Decent product. Standard aluminum channel. Light weight, easily cut-able with a hack saw (used a hack saw blade on my reciprocating saw). NOTE: All dimensionslisted on the web site were correct (thus I did not produce any pictures of that) however, the thickness WITH the plastic lens on is 8.21mm (.33"), which was not stated on the web site.Product came in elongated box. It is wrapped in plastic. The lids have a clear-coat plastic on them to keep from getting scratched. The aluminum channels are faced-to-faced together (2 pieces) with a plastic bag for each pair.At the end of the whole wrapping is the additional hardware. As stated in the description above, got 10 solid caps, 10 caps with holes (to run wire out of), 20 brackets, handful of screws (didn't count, sorry). One of the pictures created also shows close-up of the hardware (minus screws).The lid fits on nice and snug. No worries about it being loose. The plastic saran-covering keeps the plastic from scratching until ready to remove.The End caps fit nice and tight into the hole albeit, maybe not completely air-tight (slight spacing).The biggest let-down would be the brackets. Two issues here. 1) as can be seen in the pictures, not a tight fit to the aluminum channel (you can pinch the ends in to compensate for that), and 2) they are not snug against the aluminum that could product up to 2.64 mm (slightly less than 1/8 of an inch) gap between channel and whatever mounting to. Minus one-star for awareness (didn't impact me however, might others).Now, if you are mounting horizontally, then probably not much of an issue (under cabinet, etc) but if your project requires vertical mounting, it could be an issue.The shelf I was mounting these to I wanted the channel flat against the wood. To achieve that, I drilled small holes into the aluminum itself and then mounted to the wood. Was easy to drill, and even though there is a "bump" of the screw head in the channel, it did not affect my LED strips mounted directly to the channel (bumping over the head of the screw). NOTE: if you do this, you might want to put a small amount of insulator over the screw head (IE electrical tape). My LED strips did not have exposed copper on the back side, so I didn't do that.Project turned out great.

Excellent kit will definitely buy again

The track arrived in good condition. The metal track is nice but the plastic caps do not fit. They are extremely difficult to work with.